Uzebox 3D printed enclosure!
- nicksen782
- Posts: 714
- Joined: Wed Feb 01, 2012 8:23 pm
- Location: Detroit, United States
- Contact:
Re: Uzebox 3D printed enclosure!
So, turn the ISP connector upside down (and around?) and there is an opening for it on the bottom of the case? It would be like a docking station/port. Just a thought, could you also break out the expansion pins (EXT) as well? Just in case someone wants to add circuitry later. This was done on the NES although I'm not aware of any actual uses for it.
Re: Uzebox 3D printed enclosure!
Yes exactly, kinda like the NES expansion port.nicksen782 wrote:So, turn the ISP connector upside down (and around?) and there is an opening for it on the bottom of the case? It would be like a docking station/port.
I guess I could put an opening for the extension...however I don't think there would be uses specially when there's a lot of space inside anyway. Worst case it can also be cut out later with a Dremel.nicksen782 wrote:Just a thought, could you also break out the expansion pins (EXT) as well? Just in case someone wants to add circuitry later. This was done on the NES although I'm not aware of any actual uses for it.
Right now I have cut holes in the cases I have already printed.
Re: Uzebox 3D printed enclosure!
It seems like the expansion pins are placed where they are for elegant layout of the PCB. Being there, the only solutions would be desoldering and putting it on the bottom(not very useful where they are) or ribbon cable...but ribbon cable to where, the side? Extra holes in top/side isn't going to look nice, but really the kinds of things you do with the expansion pins you probably want the case off while developing. If you had a fully developed module card that fits in the case then it would be sweet. Myself, I could really go either way on even having the ISP catered to in the case design, as the Uzebox I use for development probably will stay un-cased. Just my humble opinion
- nicksen782
- Posts: 714
- Joined: Wed Feb 01, 2012 8:23 pm
- Location: Detroit, United States
- Contact:
Re: Uzebox 3D printed enclosure!
Yeah, I know. A little late for that kind of idea.
My whole thought was a type of dock that you could put the Uzebox in, just like a laptop dock where you could attach to other peripherals.
Anyway, as it appears, I am excited and really want one of these. When I tell people about the 'Retro Minimalist' game system on my desk I sometimes get the joke about it being so minimal that it's naked. Okay, actually, that only happened twice. Still, funny and worth a share for a laugh.
My whole thought was a type of dock that you could put the Uzebox in, just like a laptop dock where you could attach to other peripherals.
Anyway, as it appears, I am excited and really want one of these. When I tell people about the 'Retro Minimalist' game system on my desk I sometimes get the joke about it being so minimal that it's naked. Okay, actually, that only happened twice. Still, funny and worth a share for a laugh.
Re: Uzebox 3D printed enclosure!
So here how it looks with ISP breakout underneath:
If one wants to use it, just snap in an ISP 6 pin header, solder a ribbon cable, plug into the original ISP jack and voila! If I finally get to make a bunch of enclosures for you guys on the forums, I'd send all parts needed for that (header & flat cable). For the current version of the PCB, that's pretty much the best I can do.
If one wants to use it, just snap in an ISP 6 pin header, solder a ribbon cable, plug into the original ISP jack and voila! If I finally get to make a bunch of enclosures for you guys on the forums, I'd send all parts needed for that (header & flat cable). For the current version of the PCB, that's pretty much the best I can do.
I spent so much time trying to make everything look good. One very good use for the extension header would be the wifi module, like Adadfruit's one which use SPI. I'd connect it with a ribbon cable to the EXT header and fix the tiny module inside the case anywhere, there's plenty of space.It seems like the expansion pins are placed where they are for elegant layout of the PCB. Being there, the only solutions would be desoldering and putting it on the bottom(not very useful where they are) or ribbon cable...but ribbon cable to where, the side? Extra holes in top/side isn't going to look nice, but really the kinds of things you do with the expansion pins you probably want the case off while developing. If you had a fully developed module card that fits in the case then it would be sweet. Myself, I could really go either way on even having the ISP catered to in the case design, as the Uzebox I use for development probably will stay un-cased. Just my humble opinion
Good one!When I tell people about the 'Retro Minimalist' game system on my desk I sometimes get the joke about it being so minimal that it's naked. Okay, actually, that only happened twice. Still, funny and worth a share for a laugh.
- nicksen782
- Posts: 714
- Joined: Wed Feb 01, 2012 8:23 pm
- Location: Detroit, United States
- Contact:
Re: Uzebox 3D printed enclosure!
So, turn the header around and upside down, right? What do you mean by solder on a ribbon cable? Or was that a type-o?f one wants to use it, just snap in an ISP 6 pin header, solder a ribbon cable, plug into the original ISP jack and voila!
Re: Uzebox 3D printed enclosure!
I'll solder the cable and post more pics...So, turn the header around and upside down, right? What do you mean by solder on a ribbon cable? Or was that a type-o?
Re: Uzebox 3D printed enclosure!
Squarish controllers always seemed more retro to me, so tonight I wondered what a Uzebox controller could look like... It would reuse the internals PCB of those knockoff SNES controller I ship with my kits, hence the layout. The top graphics would be made of a custom cut vinyl sticker which can be bought inexpensively these days. I'm not committing myself to actually make one, but it's sure tempting...
These could accept also accept (I think at least) CunningFellow UzeDTV PCB. These should also be relatively easy to print due the straight bevel design. Rounded corner on the enclosure don't always look good, depend on the orientation of how it's printed.
These could accept also accept (I think at least) CunningFellow UzeDTV PCB. These should also be relatively easy to print due the straight bevel design. Rounded corner on the enclosure don't always look good, depend on the orientation of how it's printed.
Re: Uzebox 3D printed enclosure!
I'm feeling like this...
Re: Uzebox 3D printed enclosure!
I've been there. After a hard night of drinking and your buddy buys you some rounds of those girly candy shots....so you have to drink them. Just a few more..mmph..